Chapter 1: INTRODUCTION
Figure 1-1. Diesel pile hammer, right-rear, three quarter view.
Section II. DESCRIPTION AND DATA
Differences in Models
Chapter 2: INSTALLATION AND OPERATING INSTRUCTIONS
Figure 2-1. Separately packed components.
Section II. MOVEMENT TO A NEW WORKSITE
Section III. CONTROLS AND INSTRUMENTS
Section IV. OPERATION UNDER USUAL CONDITIONS
Stopping
FIGURE 2-7. Bleeding the hydraulic system.
FIGURE 2-8. Engaging the starting device.
Section V. OPERATION UNDER UNUSUAL CONDITIONS
Chapter 3: OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Table 3-1. Preventive Maintenance Checks and Services.
Figure 3-1. Fuel filter assembly, removal and installation
Section V. TROUBLESHOOTING
Section VI. LUBRICATION SYSTEM
Section VII. FUEL SYSTEM
Section VIII. HYDRAULIC CONTROL SYSTEM
Figure 3-9. Hydraulic hose, receiver, and ransmitter, removal and installation.
Section IX. STARTING DEVICE
Section X. DRIVING HEAD AND ADAPTER
Figure 3-11. Starting device, exploded view.
Figure 3-12. Pile contours fitting driving head.
Chapter 4: SHIPMENT, ADMINISTRATIVE STORAGE, AND DEMOLITION TO PREVENT ENEMY USE
Other Demolition Methods
Chapter 4: DIRECT AND GENERAL SUPPORT MAINTENANCE
Section IV. TROUBLESHOOTING
Chapter 4: REPAIR INSTRUCTIONS
Section III. FUEL SYSTEM
Figure 6-3. Fuel pump, exploded view.
Fuel Pump Drive System
Figure 6-5. Fuel pump drive system and lower cylinder, exploded view.
Figure 6-6. Fuel injector.
Section IV. CYLINDERS AND RAM
Figure 6-9. Upper cylinder, exploded view.
Recoil Dampener
FIGURE 6-10. Ram, anvil, and recoil dampener, exploded view.
Section V. HYDRAULIC CONTROL SYSTEM
Figure 6-12. Hydraulic transmitter and relief valve, exploded view
Relief Valve
Appendix A: REFERENCES - TM-5-3895-265-140055
Appendix B: BASIC ISSUE ITEMS LIST
Section II. BASIC ISSUE ITEMS
Appendix C: MAINTENANCE ALLOCATION CHART
Explanation of Columns in Section IV
Section II. MAINTENCE ALLOCATION CHART
Section II. MAINTENCE ALLOCATION CHART (Cont)
Section III. SPECIAL TOOL AND SPECIAL TEST EQUIPMENT REQUIREMENTS
Appendix D: REPAIR PARTS LIST
Explanation of Columns
Special Information - TM-5-3895-265-140065
Section II. PRESCRIBED LOAD ALLOWANCE
Section II. PRESCRIBED LOAD ALLOWANCE (Cont)
SECTION III - REPAIR PARTS FOR ORGANIZATIONAL MAINTENANCE
GROUP 01 ENGINE - TM-5-3895-265-140069
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140070
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140071
GROUP 03 FUEL SYSTEM - TM-5-3895-265-140072
GROUP 03 FUEL SYSTEM (cont) - TM-5-3895-265-140073
GROUP 22 MISCELLANEOUS BODY, CHASSIS, OR HULL AND ACCESSORY ITEMS
GROUP 43 HYDRAULIC, FLUID, AIR AND VACCUUM CONTROLS
GROUP 74 CRANES, SHOVELS, AND EARTH MOVING EQUIMENT
GROUP 74 CRANES, SHOVELS, AND EARTH MOVING EQUIMENT (Cont)
SECTION V REPAIR PARTS FOR DS AND GS MAINTENANCE
GROUP 01 ENGINE - TM-5-3895-265-140079
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140080
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140081
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140082
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140083
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140084
GROUP 03 FUEL SYSTEM - TM-5-3895-265-140085
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140086
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140087
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140088
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140089
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140090
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140092
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140093
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140094
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140095
GROUP 74-CRANES, SHOVELS AND EARTH MOVING EQUIPMENT
GROUP 74-CRANES, SHOVELS AND EARTH MOVING EQUIPMENT (Cont)
Figure D-1. Upper cylinder.
Figure D-2. Lower cylinder.
Figure D-3. Air intake cover.
Figure D-4. Ram, anvil, and recoil dampener.
Figure D-5. Lubricating oil pump.
Figure D-6. Lubricating oil filter.
Figure D-8. Starting device.
Figure D-9. Fuel injector, lines, and fittings.
Figure D-10.
Figure D-11. Pump drive.
Figure D-12. Fuel and lubricating tank.
Figure D-13. Fuel filter.
Figure D-14. Starting fluid injector.
Figure D-16. Hydraulic transmitter and relief valve.
Figure D-17. Hydraulic receiver.
Figure D-18. Driving head and adapter.
Section VII, INDEX- FEDERAL STOCK NUMBER AND REFERENCE NUMBER
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER - TM-5-3895-265-140115
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER (Cont) - TM-5-3895-265-140116
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER (Cont) - TM-5-3895-265-140117
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER (Cont) - TM-5-3895-265-140118
TM-5-3895-265-14 Hammer Pile Driver Self Powered; Diesel Driven W/Fuel Oil Tank and Lubricating Oil Tank (Link-Belt Speeder Model 180M) Manual
Figure 1-1. Diesel pile hammer, right-rear, three quarter view.
Section II. DESCRIPTION AND DATA
Differences in Models
Chapter 2: INSTALLATION AND OPERATING INSTRUCTIONS
Figure 2-1. Separately packed components.
Section II. MOVEMENT TO A NEW WORKSITE
Section III. CONTROLS AND INSTRUMENTS
Section IV. OPERATION UNDER USUAL CONDITIONS
Stopping
FIGURE 2-7. Bleeding the hydraulic system.
FIGURE 2-8. Engaging the starting device.
Section V. OPERATION UNDER UNUSUAL CONDITIONS
Chapter 3: OPERATOR AND ORGANIZATIONAL MAINTENANCE INSTRUCTIONS
Table 3-1. Preventive Maintenance Checks and Services.
Figure 3-1. Fuel filter assembly, removal and installation
Section V. TROUBLESHOOTING
Section VI. LUBRICATION SYSTEM
Section VII. FUEL SYSTEM
Section VIII. HYDRAULIC CONTROL SYSTEM
Figure 3-9. Hydraulic hose, receiver, and ransmitter, removal and installation.
Section IX. STARTING DEVICE
Section X. DRIVING HEAD AND ADAPTER
Figure 3-11. Starting device, exploded view.
Figure 3-12. Pile contours fitting driving head.
Chapter 4: SHIPMENT, ADMINISTRATIVE STORAGE, AND DEMOLITION TO PREVENT ENEMY USE
Other Demolition Methods
Chapter 4: DIRECT AND GENERAL SUPPORT MAINTENANCE
Section IV. TROUBLESHOOTING
Chapter 4: REPAIR INSTRUCTIONS
Section III. FUEL SYSTEM
Figure 6-3. Fuel pump, exploded view.
Fuel Pump Drive System
Figure 6-5. Fuel pump drive system and lower cylinder, exploded view.
Figure 6-6. Fuel injector.
Section IV. CYLINDERS AND RAM
Figure 6-9. Upper cylinder, exploded view.
Recoil Dampener
FIGURE 6-10. Ram, anvil, and recoil dampener, exploded view.
Section V. HYDRAULIC CONTROL SYSTEM
Figure 6-12. Hydraulic transmitter and relief valve, exploded view
Relief Valve
Appendix A: REFERENCES - TM-5-3895-265-140055
Appendix B: BASIC ISSUE ITEMS LIST
Section II. BASIC ISSUE ITEMS
Appendix C: MAINTENANCE ALLOCATION CHART
Explanation of Columns in Section IV
Section II. MAINTENCE ALLOCATION CHART
Section II. MAINTENCE ALLOCATION CHART (Cont)
Section III. SPECIAL TOOL AND SPECIAL TEST EQUIPMENT REQUIREMENTS
Appendix D: REPAIR PARTS LIST
Explanation of Columns
Special Information - TM-5-3895-265-140065
Section II. PRESCRIBED LOAD ALLOWANCE
Section II. PRESCRIBED LOAD ALLOWANCE (Cont)
SECTION III - REPAIR PARTS FOR ORGANIZATIONAL MAINTENANCE
GROUP 01 ENGINE - TM-5-3895-265-140069
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140070
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140071
GROUP 03 FUEL SYSTEM - TM-5-3895-265-140072
GROUP 03 FUEL SYSTEM (cont) - TM-5-3895-265-140073
GROUP 22 MISCELLANEOUS BODY, CHASSIS, OR HULL AND ACCESSORY ITEMS
GROUP 43 HYDRAULIC, FLUID, AIR AND VACCUUM CONTROLS
GROUP 74 CRANES, SHOVELS, AND EARTH MOVING EQUIMENT
GROUP 74 CRANES, SHOVELS, AND EARTH MOVING EQUIMENT (Cont)
SECTION V REPAIR PARTS FOR DS AND GS MAINTENANCE
GROUP 01 ENGINE - TM-5-3895-265-140079
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140080
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140081
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140082
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140083
GROUP 01 ENGINE (Cont) - TM-5-3895-265-140084
GROUP 03 FUEL SYSTEM - TM-5-3895-265-140085
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140086
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140087
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140088
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140089
GROUP 03 FUEL SYSTEM (Cont) - TM-5-3895-265-140090
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140092
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140093
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140094
GROUP 43 HYDRAULIC, FLUID, AIR AND VACUUM CONTROLS (Cont) - TM-5-3895-265-140095
GROUP 74-CRANES, SHOVELS AND EARTH MOVING EQUIPMENT
GROUP 74-CRANES, SHOVELS AND EARTH MOVING EQUIPMENT (Cont)
Figure D-1. Upper cylinder.
Figure D-2. Lower cylinder.
Figure D-3. Air intake cover.
Figure D-4. Ram, anvil, and recoil dampener.
Figure D-5. Lubricating oil pump.
Figure D-6. Lubricating oil filter.
Figure D-8. Starting device.
Figure D-9. Fuel injector, lines, and fittings.
Figure D-10.
Figure D-11. Pump drive.
Figure D-12. Fuel and lubricating tank.
Figure D-13. Fuel filter.
Figure D-14. Starting fluid injector.
Figure D-16. Hydraulic transmitter and relief valve.
Figure D-17. Hydraulic receiver.
Figure D-18. Driving head and adapter.
Section VII, INDEX- FEDERAL STOCK NUMBER AND REFERENCE NUMBER
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER - TM-5-3895-265-140115
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER (Cont) - TM-5-3895-265-140116
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER (Cont) - TM-5-3895-265-140117
CROSS-REFERENCE TO FIGURE AND ITEM NUMBER (Cont) - TM-5-3895-265-140118
TM-5-3895-265-14 Hammer Pile Driver Self Powered; Diesel Driven W/Fuel Oil Tank and Lubricating Oil Tank (Link-Belt Speeder Model 180M) Manual
